SWR0J-20SOW Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network 0Ω - Zero Ohm Jumper Network 10 mils Silicon/Quartz Si/SiO2 28 x 177 mils manufactured by Semiconwell SWR0J-20SOW Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network 0Ω - Zero Ohm Jumper Network 10 mils Silicon/Quartz Si/SiO2 28 x 177 mils manufactured by Semiconwell SEMICONWELL Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SOICW-20 20 leads Integrated Passive Networks SWR0J-20SOW FEATURES APPLICATIONS 0Ω - Zero Ohm Jumper Network 283mΩ jumpers network Available in 6 connections configurations Packed in standard SOICW-20 package Custom configurations are available Alter PC Boards functionality Programmable circuit interconnect PC Boards crossovers Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW PRODUCT DESCRIPTION AND SHORT APPLICATION NOTE Semiconwell integrated zero ohms jumper arrays SWR0J-20SOW are designed to be used in a wide range of applications including PC Board crossovers, permanent jumpers, program, customize or alter functionality of a PC Board. Due to a very low capacitance between jumpers, these can be used also on high-speed data lines. The SW R0J series solution saves board space, improves PC Board performance and reduces assembly cost on passive components. These devices can be used over the full military temperature range -55°C to +125°C. Quality and workmanship is per MIL-S-883. TECHNOLOGY DESCRIPTION: SEMICONDUCTOR-THIN FILM MANUFACTURING Integrated passive networks are manufactured using advanced thin film technologies including ultra -stable and self passivating Tantalum Nitride resistors, gold interconnect metallization and reliable MNOS capacitors to achieve excellent uniformity, performance and reliability. Thin film resistor technology is the preferred solution for all applications that require low noise, long term stability and excellent performance at very high frequencies. Semiconwell employs proprietary thin film technologies for deposition of a wide range of sheet resistance films from from 1Ω/sq to 10,000Ω/sq. All Semiconwell's products are available in die form and as KGD, known good die and are ideal for high reliability hybrid and multi chip module applications. Besides thin film resistors, Semiconwell integrates capacitors, Schottky diodes, Zener diodes and transistors. Integrated passive and active networks are manufactured using Semiconwell's in house high reliability semiconductor manufacturing processes. All semiconductor devices employ precision doping via ion implantation, silicon nitride junction passivation, platinum silicided contacts and gold interconnect metallization for best performance and reliability. MNOS capacitors and Tantalum Nitride resistors are easily integrated with Schottky diodes to provide complete standard and custom RCD solutions. In die form, these products are ideal for hybrid and multi chip module applications. In packaged form, these products are the best solution where space and weight are a concern. All Semiconwell's products are manufactured using GOLD CHIP TECHNOLOGY™ a trade mark of Semiconix Corporation. ELECTRICAL CHARACTERISTICS @25°C PARAMETER VALUE UNITS DC resistance 0.283 Ω DC resistance tolerance 20 % Power rating (die) @70°C 1822 mW Capacitance (per jumper) 2.71 pF Fusing current 0.65 A Minimum operating temperature -55 °C Maximum operating temperature 125 °C Note: Stresses beyond listed absolute maximum ratings may cause permanent damage to the device. 0Ω - Zero Ohm Jumper Network - GENERAL DIE INFORMATION SUBSTRATE THICKNESS [mils] DIE SIZE LxW [mils] Silicon/Quartz (Si/SiO2) 10±2 177x28±3 (4.50x0.71±0.08 mm) CONDUCTOR BONDING PADS BACKSIDE METAL Conductor is Gold (Au), 3µm thick. The bonding pads of the zero ohms jumpers are min. 4x4 mils, 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands 30 min at 400°C in air without loss of adhesion. Backside of the die is metallized with standard Si/Au compatible with eutectic and epoxy die attach. Custom metallizations are available upon special request for die products only. 0Ω - Zero Ohm Jumper Network - PIN CONNECT LAYOUT & PACKAGE SPECIFICATIONS Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW Note: Image show pin inter connection layout. Layout of the die might differ. Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW INSTANT QUOTE Semiconwell P/N Quantity E-mail ORDERING: DELIVERY: SHIPPING/PACKAGING: SAMPLES: GUARANTEED SUPPLY! Semiconwell guarantees continuous supply and availability of all standard products provided minimum order quantities are met. Home Product Tree Tech. Support PDF Request Quote Inventory Place Order Contact sales

 
 
SEMICONWELL   Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network
SOICW-20 20 leads
Integrated Passive Networks   SWR0J-20SOW
 
 

FEATURES
APPLICATIONS
0Ω - Zero Ohm Jumper Network
283mΩ jumpers network
Available in 6 connections configurations
Packed in standard SOICW-20 package
Custom configurations are available
Alter PC Boards functionality
Programmable circuit interconnect
PC Boards crossovers
Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW

PRODUCT DESCRIPTION AND SHORT APPLICATION NOTE
Semiconwell integrated zero ohms jumper arrays SWR0J-20SOW are designed to be used in a wide range of applications including PC Board crossovers, permanent jumpers, program, customize or alter functionality of a PC Board. Due to a very low capacitance between jumpers, these can be used also on high-speed data lines. The SW R0J series solution saves board space, improves PC Board performance and reduces assembly cost on passive components. These devices can be used over the full military temperature range -55°C to +125°C. Quality and workmanship is per MIL-S-883.

TECHNOLOGY DESCRIPTION: SEMICONDUCTOR-THIN FILM MANUFACTURING
Integrated passive networks are manufactured using advanced thin film technologies including ultra -stable and self passivating Tantalum Nitride resistors, gold interconnect metallization and reliable MNOS capacitors to achieve excellent uniformity, performance and reliability. Thin film resistor technology is the preferred solution for all applications that require low noise, long term stability and excellent performance at very high frequencies. Semiconwell employs proprietary thin film technologies for deposition of a wide range of sheet resistance films from from 1Ω/sq to 10,000Ω/sq.
All Semiconwell's products are available in die form and as KGD, known good die and are ideal for high reliability hybrid and multi chip module applications. Besides thin film resistors, Semiconwell integrates capacitors, Schottky diodes, Zener diodes and transistors.
Integrated passive and active networks are manufactured using Semiconwell's in house high reliability semiconductor manufacturing processes. All semiconductor devices employ precision doping via ion implantation, silicon nitride junction passivation, platinum silicided contacts and gold interconnect metallization for best performance and reliability. MNOS capacitors and Tantalum Nitride resistors are easily integrated with Schottky diodes to provide complete standard and custom RCD solutions. In die form, these products are ideal for hybrid and multi chip module applications. In packaged form, these products are the best solution where space and weight are a concern.
All Semiconwell's products are manufactured using GOLD CHIP TECHNOLOGY™ a trade mark of Semiconix Corporation.

ELECTRICAL CHARACTERISTICS @25°C
PARAMETER VALUE UNITS
DC resistance 0.283 Ω
DC resistance tolerance 20 %
Power rating (die) @70°C 1822 mW
Capacitance (per jumper) 2.71 pF
Fusing current 0.65 A
Minimum operating temperature -55 °C
Maximum operating temperature 125 °C
Note: Stresses beyond listed absolute maximum ratings may cause permanent damage to the device.

0Ω - Zero Ohm Jumper Network - GENERAL DIE INFORMATION
SUBSTRATE THICKNESS [mils] DIE SIZE LxW [mils]
Silicon/Quartz
(Si/SiO2)
10±2 177x28±3 (4.50x0.71±0.08 mm)
CONDUCTOR BONDING PADS BACKSIDE METAL
Conductor is Gold (Au), 3µm thick. The bonding pads of the zero ohms jumpers are min. 4x4 mils, 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands 30 min at 400°C in air without loss of adhesion. Backside of the die is metallized with standard Si/Au compatible with eutectic and epoxy die attach. Custom metallizations are available upon special request for die products only.
Delivery for packaged integrated passive networks standard products is 4-6 weeks ARO. Certain items may be available from stock. For standard products available from stock, there is a minimum line item order of $250.0. Inventory is periodically updated. For 2500pc or larger orders, all surface mount packaged devices are shipped in tape on reel (T/R). For smaller quantities, it may vary. Samples are available only for customers that have issued firm orders pending qualification of product in a particular application. On line Orders have to be verified, accepted and acknowledged by Semiconwell sales department in writing before, becoming non cancelable binding contracts.

0Ω - Zero Ohm Jumper Network - PIN CONNECT LAYOUT & PACKAGE SPECIFICATIONS
Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW
Note: Image show pin inter connection layout. Layout of the die might differ.
Silicon/Quartz [Si/SiO2] Zero Ohm Jumper Network SWR0J-20SOW

SWR0J-20SOW available pin connections
NamePins connectionsDatasheetDrawing
1C11-20, 2-19, 3-18, 4-17, 5-16, 6-15, 7-14, 8-13, 9-12, 10-11SWR0J-20SOW-C1
2Q12-19, 3-18, 4-17, 5-16, 6-15, 7-14, 8-13, 9-12, 10-11SWR0J-20SOW-Q1
3Q22-18, 3-17, 4-16, 5-15, 6-14, 7-13SWR0J-20SOW-Q2
4Q31-19, 2-18, 3-17, 4-16, 5-15, 6-14, 7-13, 8-12SWR0J-20SOW-Q3
5Q42-18, 3-17, 4-16, 5-15, 6-14, 7-13, 8-12SWR0J-20SOW-Q4
6Q52-18, 3-17, 4-16, 5-15, 6-14, 7-13, 8-12, 9-11SWR0J-20SOW-Q5

STANDARD PRODUCTS ORDERING INFORMATION
CONNECTIONSW P/NPACKAGEMIN. QTYU/P [$]ORDER
C1SWR0J-20SOW-C1SOICW-20RFQ
Q1SWR0J-20SOW-Q1SOICW-20RFQ
Q2SWR0J-20SOW-Q2SOICW-20RFQ
Q3SWR0J-20SOW-Q3SOICW-20RFQ
Q4SWR0J-20SOW-Q4SOICW-20RFQ
Q5SWR0J-20SOW-Q5SOICW-20RFQ

STANDARD PRODUCTS AVAILABLE FROM STOCK
SW P/NMIN. QTYU/P [$]ORDERQTYU/P [$]ORDER
SWR0J-20SOW-Q5RFQ36RFQ
SWR0J-20SOW-Q5RFQ350RFQ
SWR0J-20SOW-Q5RFQ1825RFQ
SWR0J-20SOW-Q4RFQ2000RFQ

List prices are for standard products, available from stock. List prices for other quantities and tolerances are available on line through Instant Quote. For standard products available from stock, there is a minimum line item order. For custom products please inquire by contacting SEMICONWELL technical sales. No rights can be derived from pricing information provided on this website. Such information is indicative only, is showed for budgetary use only and subject to change by SEMICONWELL at any time and without notice.
For custom products sold as bare tested die or known good die KGD, minimum order is 5000pc. Dice are 100% functional tested, visual inspected and shipped in antistatic waffle packs. For special die level KGD requirements, different packaging or custom configurations, contact SEMICONWELL sales.

INSTANT QUOTE
Semiconwell P/N Quantity E-mail    
 

ORDERING: Order on line HERE. A copy of the order along with an order confirmation receipt is issued instantly for all orders placed on line. On line Orders have to be verified, accepted and acknowledged by US Microwaves sales department in writing before, becoming non cancelable binding contracts.
DELIVERY: Delivery for packaged integrated passive networks standard products is 4-6 weeks ARO. Certain items may be available from stock. For standard products available from stock, there is a minimum line item order of $250.0. Inventory is periodically updated. For 2500pc or larger orders, all surface mount packaged devices are shipped in tape on reel (T/R). For smaller quantities, it may vary. Samples are available only for customers that have issued firm orders pending qualification of product in a particular application. On line Orders have to be verified, accepted and acknowledged by Semiconwell sales department in writing before, becoming non cancelable binding contracts.
SHIPPING/PACKAGING: All surface mount packaged devices are shipped in tape on reel (T/R). All devices for chip and wire applications are 100% tested, visual inspected and shipped in waffle packs (WP). For larger orders,>10k pc, devices can be shipped on film frame. For smaller quantities, it may vary. For high volume automated assembly, devices may be supplied as 4" wafers 100% tested, inked and diced on expanded film frame (FF).
SAMPLES: Samples are available only for customers that have issued firm orders pending qualification of product in a particular application.

GUARANTEED SUPPLY! Semiconwell guarantees continuous supply and availability of all standard products provided minimum order quantities are met.

Semiconwell has made every effort to have this information as accurate as possible. However, no responsibility is assumed by Semiconwell for its use, nor for any infringements of rights of third parties which may result from its use. Semiconwell reserves the right to revise the content or modify its product line without prior notice. Semiconwell products are not authorized for and should not be used within support systems which are intended for surgical implants into the body, to support or sustain life, in aircraft, space equipment, submarine, or nuclear facility applications without the specific written consent of Semiconwell.


Last update: July 18, 2013
SEMICONWELL 2108 Bering Dr. San Jose, CA 95131 Tel:(408)986-8026 Fax:(408)986-8027
©1990-2018 SEMICONWELL All rights reserved. No material from this site may be used or reproduced without permission.