PAC27A01,Vishay MPM series of SOT-23 molded thin film dividers same as SWRV PRECISION VOLTAGE DIVIDER NETWORK manufactured by SEMICONWELL, VOLTAGE DIVIDERS,VOLTAGE DIVIDER NETWORKS-SEMICONWELL - Thin film Precision voltage divider network SOT 23 Voltage divider, Precision voltage dividers network SWRV XXX/XXX series. Voltage divider SWRV-xx/xx is available in wide resistance range 10 ohm to 1 meg ohm , tolerance ±0.1%, ratios ±0.05% Low temperature coefficient ±25ppm/°C Long term stability, 0.05% after 1000 hours Voltage dividers are  available in any  custom values and configuration. Applications include Precision voltage dividers, OP AMP gain control Attenuation Pull-up/pull-down TTL/MOS interfacing Precision voltage divider resistor array offers a high degree of stability, low noise and the proven reliability characteristics of Tantalum Nitride. These devices are manufactured using advanced Thin Film Technology. A wide range of resistor values is available, as well as various tolerances and TCRs. Integrated passive networks are manufactured using advanced thin film technologies including ultra-stable and self passivating Tantalum Nitride resistors, gold interconnect metallization and reliable MNOS capacitors to achieve excellent uniformity, performance and reliability. Thin film resistor technology is the preferred solution for all applications that require low noise, long term stability and excellent performance at very high frequencies. Semiconwell employs proprietary thin film technologies for deposition of a wide range of sheet resistance films from 1Ω/sq to 10,000 Ω/sq. All Semiconwell's products are available in die form and are ideal for high reliability hybrid and multi chip module applications.

 
 
SEMICONWELL
Integrated Passive Networks
  THIN FILM PRECISION VOLTAGE DIVIDER NETWORK
SWRV/RXXX/RXXX
 
 

FEATURES
APPLICATIONS
SCHEMATIC
Wide resistance range 10 to 1MΩ
Tolerance ±0.1%, ratios ±0.01%
Low temperature coefficient ±25ppm/°C, Long term stability, 0.05% after 1000 hours
Available in bare die, flip-chip 0201, 0402, and standard 3 leads packages
Available for High Voltage as SWRHV series
Also available in custom values and configuration
Precision voltage divider
OP AMP gain control
Precise Attenuation
Pull-up/pull-down
TTL/MOS interfacing
 

SHORT PRODUCT APPLICATION NOTE
Precision voltage divider resistor array offers a high degree of stability, low noise and the proven reliability characteristics of Tantalum Nitride. These devices are manufactured using advanced Thin Film Technology. A wide range of resistor values is available, as well as various tolerances and TCRs.

SEMICONDUCTOR-THIN FILM MANUFACTURING PROCESS DESCRIPTION
Integrated passive networks are manufactured using advanced thin film technologies including ultra -stable and self passivating Tantalum Nitride resistors, gold interconnect metallization and reliable MNOS capacitors to achieve excellent uniformity, performance and reliability. Thin film resistor technology is the preferred solution for all applications that require low noise, long term stability and excellent performance at very high frequencies. Semiconwell employs proprietary thin film technologies for deposition of a wide range of sheet resistance films from 1 Ω/sq to 10,000 Ω/sq. All Semiconwell's products are available in die form and as KGD, known good die and are ideal for high reliability hybrid and multi chip module applications. Besides thin film resistors, Semiconwell integrates capacitors, Schottky diodes, Zener diodes and transistors. Integrated passive and active networks are manufactured using Semiconwell's in house high reliability semiconductor manufacturing processes. All semiconductor devices employ precision doping via ion implantation, silicon nitride junction passivation, platinum silicided contacts and gold interconnect metallization for best performance and reliability. MNOS capacitors and Tantalum Nitride resistors are easily integrated with Schottky diodes to provide complete standard and custom RCD solutions. In die form, these products are ideal for hybrid and multi chip module applications. In packaged form, these products are the best solution where space and weight are a concern.

RESISTOR SPECIFICATIONS
Capacitance [pF] Tolerance q [%] Power Rating [mW]
<5pF Absolute:±0.05 to ±5
Ratio: ±0.5 to ±0.01
200 mW@70°C

Stresses beyond listed absolute maximum ratings may cause permanent damage to the device.

ELECTRICAL CHARACTERISTICS
PARAMETER VALUE UNITS
TCR,Absolute, -55 to +125 °C max.±25 ppm/°C
Operating Voltage,-55 to +125 °C max 100 Vdc
Power Rating (per resistor) @70°C (Derate linearly to zero @150°C) max 100 mW
Thermal Shock, Method 107 MIL-STD-202F max ±0.5 % @DR
High Temperature Exposure,100Hrs@150°C Ambient max ±0.25 % @DR
Moisture Resistance, Method 106 MIL-STD-202F max ±0.5 % @DR
Life, Method 108 MIL-STD-202F (125°C/1000hr) max ±0.5 % @DR
Noise, Method 308 MIL-STD-202F
For R>250kΩ
max -25
typ. -20
dB
Resistor Ratio Tolerance (R1/R2 @25°C) ±0.5 to ±0.01 %
Insulation Resistance @25°C min 1012 Ω
Shelf  Life Stability (Ratio) 1 yr @25°C 50 ppm
Moisture Sensitivity Level 1 (per IPC/JEDEC ) 1 1

GENERAL DIE INFORMATION
Substrate Thickness (mils) Die size (mils) Bonding pads Backside metal
SiO2 / Silicon 10±2 35 x 35 ±3 4x4 mils, 3mm thick, 99.99% electroplated gold with a TiW barrier Au/Si compatible with eutectic and conductive epoxy die attach.
All Semiconwell products are available in die form for chip and wire hybrid circuits and multi chip modules applications. Typical delivery for standard die products is 3-4 weeks ARO. For Chip Scale Packaged (CSP) devices consult factory for an update on availability of certain products.

CONDUCTORS RESISTORS BACKSIDE METAL
The bonding pads of the resistors are 3µm thick, 99.99% electroplated gold with a TiW barrier that withstands 30 min at 400°C in air without loss of adhesion. Resistive material is ultra stable TaN with low TCR <75ppm/°C typical. For Rsq<10Ω/sq and Rsq>500Ω/sq, the resistive material is proprietary. Power rating/resistor max 100mW for R<1KΩ and 25mW for R>1KΩ. Standard tolerance is ±5%. Backside of the die is metallized with standard Si/Au compatible with eutectic and epoxy die attach. Custom metallizations are available upon special request for die products only.

DIE LAYOUT PACKAGE PIN OUT
voltage divider layout
V1=1
V2=2
Vref=3
 

STANDARD PRODUCTS ORDERING INFORMATION

R1(Ω) R2(Ω) R CODE SOT23 BARE DIE
12400 20000 12K4/20K0 SWRV/12K4/20K0-ST SWRV-12K4/20K0-BD
10 to 10M 10 to 10M XXX/XXX SWRV/XXX/XXX-ST SWRV-XXX/XXX-BD

SW PART # QUANTITY PACKAGED U/P($) BARE DIE U/P($)
SWRV/RCODE-1%-R0.5%   5,000pc -SOT23   -BD  
SWRV/RCODE-0.5%-R0.1%   5,000pc -SOT23   -BD  
SWRV/RCODE-0.25%-R0.1%    5,000pc -SOT23   -BD  
SWRV/RCODE-0.1%-R0.1%    5,000pc -SOT23   -BD  
SWRV/RCODE-0.1%-R0.05%    5,000pc -SOT23   -BD  
SWRV/RCODE-0.1%-R0.25%      5,000pc -SOT23   -BD  
SWRV/RCODE-0.1%-R0.25%      5,000pc -SOT23   -BD  
For custom products sold as bare tested die or known good die KGD, minimum order is 5000pc. Dice are 100% functional tested, visual inspected and shipped in antistatic waffle packs. For special die level KGD requirements, different packaging or custom configurations, contact sw_sales@semiconwell.com
CUSTOM PRODUCTS ORDERING INFORMATION - P/N BUILDER

R1 R1 multiplier R2 R2 multiplier Absolute Ratio Package
R1 R1 multiplier R2 R2 multiplier Tolerance Tolerance Package
Find part #
  RoHS
Note1: The first 3 digits are significant figures and the last digit specifies the number of zeros to follow (10 exponent), i.e. (nnn)x10M. If less than 4 digits, it means the absolute value, and it might include decimal point.
Note2: For different values than listed on P/N Builder above (standard EIA E192), please use the RFQ link located on the bottom of this page.

INSTANT QUOTE
Semiconwell P/N Quantity E-mail    
 

Delivery for packaged Resistor networks standard products is 4-6 weeks ARO. Certain items may be available from stock. For standard products available from stock, there is a minimum line item order of $250.0. Inventory is periodically updated. For 2500pc or larger orders, all surface mount packaged devices are shipped in tape on reel (T/R). For smaller quantities, it may vary. Samples are available only for customers that have issued firm orders pending qualification of product in a particular application. On line Orders have to be verified, accepted and acknowledged by Semiconwell sales department in writing before, becoming non cancelable binding contracts.

Semiconwell guarantees continuous supply and availability of any of it's standard products provided minimum order quantities are met.

SEMICONWELL has made every effort to have this information as accurate as possible. However, no responsibility is assumed by SEMICONWELL for its use, nor for any infringements of rights of third parties which may result from its use. SEMICONWELL reserves the right to revise the content or modify its product line without prior notice. SEMICONWELL products are not authorized for and should not be used within support systems which are intended for surgical implants into the body, to support or sustain life, in aircraft, space equipment, submarine, or nuclear facility applications without the specific written consent.

Home Product Tree Tech. Support Print PDF Packages Request Quote Inventory Place Order Contact sales